hydra.asutexas.edu

 


 


 




 

High-Resolution Spectrograph (decommissioned)


The HRS was a single channel adaptation of the ESO UVES spectrometer as described by Tull. ("High-Resolution Fiber-Coupled Spectrograph of the Hobby-Eberly Telescope," SPIE Conf. 3355-21, Kona, March 1998 (pdf)). It uses an R-4 echelle mosaic with cross-dispersing gratings to separate spectral orders. An all-refracting camera images onto a mosaic of two thinned and anti-reflection coated 2K x 4K CCDs with 15 micron pixels. The CCDs are abutted along their 4K side with a ~72 pixel dead space between them. This dead space is approximately parallel to the spectral orders. Resolving powers of R ~ 15,000, 30,000, 60,000, and 120,000 are available by means of four effective slit widths. Spectral coverage is 420 - 1100 nm. The HRS was commissioned in March 2001.

N.B., this information applies to the original HRS, which has been decommissioned and will be replaced by HRS-2 at a time to be determined.

Overall Description

The HET HRS spectral resolving power ranges from R = 15,000 - 120,000, with full spectral coverage on a mosaic of two Marconi CCDs, each with 2048 x 4100 15 µm pixels. The HRS is a "white pupil" spectrograph using the 2-mirror collimator system pioneered by Hans Dekker and Bernard Delabre at ESO: Mirror M1, the main collimator, is an off-axis paraboloid used in auto-collimation, with the entrance slit at its focus. After the dispersed light is reflected from M1 the beam comes to an intermediate focus, offset from the slit by an amount controlled by the off-plane tilt of the echelle, which is 0.8°i;. Mirror M2 has identical figure and focal length but is farther off-axis by a distance equal to the separation of slit and intermediate focus; it serves to

  1. re-collimate the beam, directing all dispersed rays to the white pupil coinciding with the surface of the cross-dispersing grating, and
  2. compensate for the off-axis aberrations of M1.
Mirrors M1 and M2 share a common axis and focal point. The parameters of the system are summarized in the table below.

The "R-4" Echelle

The echelle is a mosaic of two R-3.75 gratings replicated on a single blank at the Richardson Gratings Lab of Spectronic Instruments Inc.

  • Dimensions: 210 x 836 mm Ruled Area with 14 mm gap between rulings
  • Blaze Angle: 75.07° (R-3.75; i.e., tan 75.07 = 3.75)
  • Grooves/mm: 31.6

Cross Dispersing Gratings

  • Dimensions:
    1. 204 x 254 mm Ruled Area
    2. 210 x 250 mm Ruled Area
  • Rulings:
    1. 316 gr/mm at blaze angle 6.80°
    2. 600 gr/mm at blaze angle 9.53°
  • Included Angle: 43.41°

N.B., this information applies to the original HRS, which has been decommissioned and will be replaced by HRS-2 at a time to be determined.

Setups

For spectral stability we chose to allow the echelle and gratings tilts to be varied only in fixed steps. Both the echelle and the cross-disperser grating tilts are selectable in 1° intervals. For the echelle, the exact interval is not yet determined, however for ease of alignment we are currently considering settings that would place the red He-Ne laser line in the center of the CCD for two setups. These settings will translate the blaze maximum +23.5 mm and +15.3 mm, corresponding typically to a wavelength shift of half the free spectral range. For most applications no shift should be needed unless, e.g., a spectral feature of interest falls on a blemish of the CCD. This shift also allows spectral observations in the near-infrared, where the free spectral range is slightly greater than the width of the CCD. This will occur for wavelengths greater than 910 nm. For the cross-disperser gratings, the 1° tilt intervals are not adjustable. Table 2 below lists the relevant data for the available tilt settings and the Schott filter that should be used for each setting for blocking the second-order spectra. For convenience, Columns 9-11 list the second-order spectra. These are to be blocked by the Schott filters listed in column 12.

See the HRS Configurations Check script to see if an HRS configuration is valid or not.

N.B., this information applies to the original HRS, which has been decommissioned and will be replaced by HRS-2 at a time to be determined.





Last updated: Fri, 29 Dec 2023 11:51:23 +0000 stevenj



Overview

The Telescope

Technical Overview

Object Observability

Performance

Non-sidereal observations

Instruments

LRS2

LRS2 Summary

LRS2 Details

LRS2 Fiber Layout and Position Angle

LRS2 Throughput

LRS2 Observing details

VIRUS

VIRUS - Summary

VIRUS - Setting up on targets

VIRUS - Misc details

VIRUS - Throughput and sensitivity

VIRUS - low surface brightness sensitivity

VIRUS - Dithers, IFUs, Tiling

VIRUS - Tiling observations

Habitable Zone Planet Finder (HPF)

HPF Details

HPF Setting up on targets

HPF Throughput and Exposure Meter

HPF Data Reductions

HRS-2 (in development)

HRS-2 Summary

HRS-2 Details

HRS-2 configurations

HRS-2 exposure meter

HRS-2 Position Angle and Fiber layout

HRS-2 Throughput

Old Instruments

HRS - old

LRS - old

MRS - old

Program Preparation

Web Management System